Cost to Load-Bearing Wall Removal in Minneapolis, MN (2026)
If you’re budgeting a load-bearing wall removal in Minneapolis, most projects run $1,626-$8,672, 8% above the $3,500 national average. What moves that number most is usually one thing: Wall Length and Load Above. On its own it can swing the cost by $500 - $4,000, so that’s the decision to slow down on before you sweat the smaller stuff.
Easiest place to save: Do your own demolition. Removing drywall and hauling debris before the structural crew arrives can save $300-$600 in labor costs.
In the Midwest (where Minneapolis sits): Competitive contractor market keeps prices moderate. Basement homes may have existing beam-and-post systems that simplify load path design.
$1,626-$8,672 in Minneapolis
8% above the national average · 1.08x cost multiplier
In Minneapolis, a load-bearing wall removal runs $1,626 to $8,672 on average - about 8% above what homeowners pay nationwide. The Midwest market's labor costs account for most of the gap, with material pricing and local permitting fees adding to the spread. Use the cost table below to compare budget, mid-range, and premium options side by side.
Cost Breakdown in Minneapolis
| Line Item | Low | Mid | High |
|---|---|---|---|
| Cost per linear ft | $108 | $271 | $542 |
| Materials | $410 | $820 | $1,845 |
| Labor | $1,364 | $2,273 | $3,977 |
| Permits | $205 | $359 | $513 |
| Design | $205 | $513 | $1,230 |
| Total | $2,184+9% vs. national avg | $3,965+9% vs. national avg | $7,565+8% vs. national avg |
Budget
Short wall (6-8 linear ft) with simple load path, standard LVL beam, minimal mechanical rerouting, basic drywall patching
Mid-Range
Medium wall (10-14 linear ft) with engineered steel or LVL beam, some electrical/plumbing rerouting, full drywall finish and paint
Premium
Long wall (16-20+ linear ft) with steel I-beam, significant mechanical rerouting, structural engineering, concealed beam with flush ceiling finish
Material Options
Material prices below are national averages; availability in Minneapolis may shift costs slightly.
| Material | Cost/Unit | Best For |
|---|---|---|
| LVL (Laminated Veneer Lumber) Beam | $8-$20 per linear ft of beam | Spans under 14 feet in single-story homes or where the beam can be hidden in ceiling framingAffordable, widely available, easy to cut on site, can be concealed in standard ceiling framing |
| Steel I-Beam | $30-$80 per linear ft of beam | Long spans over 14 feet, multi-story load paths, or situations where minimum beam depth is criticalHandles the longest spans, thinnest profile for a given load, extremely strong, no deflection issues |
| Glulam (Glued Laminated Timber) Beam | $12-$30 per linear ft of beam | Open-concept designs where the beam will be left exposed as an architectural featureAttractive for exposed applications, strong, available in long lengths, sustainable material |
| PSL (Parallel Strand Lumber) Beam | $10-$25 per linear ft of beam | High-load situations where steel is not desired and the beam will be concealedVery strong, consistent quality, good for heavy loads, available in large sizes |
| Flush Beam (Recessed into Ceiling) | $40-$80 per linear ft installed | Open-concept living spaces where a visible beam would disrupt the ceiling lineInvisible after installation, maintains flat ceiling line, cleanest finished appearance |
Other Projects in Minneapolis
Minneapolis Estimate
Typical Range
$1,626-$8,672
vs. National Average
8% above national
Cost Multiplier
1.08x
Cost Per linear ft
$108-$542
This 1.08x estimate prices Minneapolis labor from BLS Occupational Employment and Wage Statistics (May 2025) and applies a lighter regional adjustment to materials and permits, which vary less by metro than labor does. Actual bids vary by contractor, project scope, and timing.
See national average costs →