Cost to Load-Bearing Wall Removal in Albuquerque, NM (2026)
If you’re budgeting a load-bearing wall removal in Albuquerque, most projects run $1,395-$7,443, 7% below the $3,500 national average. What moves that number most is usually one thing: Wall Length and Load Above. On its own it can swing the cost by $500 - $4,000, so that’s the decision to slow down on before you sweat the smaller stuff.
Easiest place to save: Do your own demolition. Removing drywall and hauling debris before the structural crew arrives can save $300-$600 in labor costs.
In the Southwest (where Albuquerque sits): Snow loads in mountain areas may require larger beams. Growing markets in Denver and Salt Lake City push labor costs slightly above average.
$1,395-$7,443 in Albuquerque
7% below the national average · 0.93x cost multiplier
Expect to pay $1,395-$7,443 for a load-bearing wall removal in Albuquerque, about 7% below the national benchmark. The Southwest region's contractor market and material costs account for most of this difference. The detailed breakdown below shows how budget, mid-range, and premium projects compare at Albuquerque prices.
Cost Breakdown in Albuquerque
| Line Item | Low | Mid | High |
|---|---|---|---|
| Cost per linear ft | $93 | $233 | $465 |
| Materials | $384 | $768 | $1,728 |
| Labor | $1,085 | $1,808 | $3,164 |
| Permits | $192 | $336 | $480 |
| Design | $192 | $480 | $1,152 |
| Total | $1,853-7% vs. national avg | $3,392-7% vs. national avg | $6,524-7% vs. national avg |
Budget
Short wall (6-8 linear ft) with simple load path, standard LVL beam, minimal mechanical rerouting, basic drywall patching
Mid-Range
Medium wall (10-14 linear ft) with engineered steel or LVL beam, some electrical/plumbing rerouting, full drywall finish and paint
Premium
Long wall (16-20+ linear ft) with steel I-beam, significant mechanical rerouting, structural engineering, concealed beam with flush ceiling finish
Material Options
Material prices below are national averages; availability in Albuquerque may shift costs slightly.
| Material | Cost/Unit | Best For |
|---|---|---|
| LVL (Laminated Veneer Lumber) Beam | $8-$20 per linear ft of beam | Spans under 14 feet in single-story homes or where the beam can be hidden in ceiling framingAffordable, widely available, easy to cut on site, can be concealed in standard ceiling framing |
| Steel I-Beam | $30-$80 per linear ft of beam | Long spans over 14 feet, multi-story load paths, or situations where minimum beam depth is criticalHandles the longest spans, thinnest profile for a given load, extremely strong, no deflection issues |
| Glulam (Glued Laminated Timber) Beam | $12-$30 per linear ft of beam | Open-concept designs where the beam will be left exposed as an architectural featureAttractive for exposed applications, strong, available in long lengths, sustainable material |
| PSL (Parallel Strand Lumber) Beam | $10-$25 per linear ft of beam | High-load situations where steel is not desired and the beam will be concealedVery strong, consistent quality, good for heavy loads, available in large sizes |
| Flush Beam (Recessed into Ceiling) | $40-$80 per linear ft installed | Open-concept living spaces where a visible beam would disrupt the ceiling lineInvisible after installation, maintains flat ceiling line, cleanest finished appearance |
Other Projects in Albuquerque
Albuquerque Estimate
Typical Range
$1,395-$7,443
vs. National Average
7% below national
Cost Multiplier
0.93x
Cost Per linear ft
$93-$465
This 0.93x estimate prices Albuquerque labor from BLS Occupational Employment and Wage Statistics (May 2025) and applies a lighter regional adjustment to materials and permits, which vary less by metro than labor does. Actual bids vary by contractor, project scope, and timing.
See national average costs →