Cost to Home Network / Structured Wiring in Los Angeles, CA

$1,350–$8,100 in Los Angeles

35% above the national average · 1.35x cost multiplier

In Los Angeles, a home network / structured wiring runs $1,350 to $8,100 on average — about 35% above what homeowners pay nationwide. The West Coast market's labor costs account for most of the gap, with material pricing and local permitting fees adding to the spread. Use the cost table below to compare budget, mid-range, and premium options side by side.

Cost Breakdown in Los Angeles

Line Item	Low	Mid	High
Cost per per drop	$135	$270	$810
Materials	$540	$2,025	$4,725
Labor	$405	$1,620	$4,050
Permits	$0	$0	$0
Total	$945+35% vs. national avg	$3,915+35% vs. national avg	$9,450+35% vs. national avg

Budget

3-4 Cat6 data drops to main living areas, central patch panel, basic wall plates - typical existing home upgrade for better wired connectivity

Mid-Range

8-12 Cat6 drops throughout home, structured media center or network rack, patch panel, wall-mounted access points, coax drops for TVs

Premium

Full structured wiring package - 15-20 Cat6A drops, fiber backbone, enterprise-grade access points (Ubiquiti, Cisco Meraki), security camera wiring, full equipment rack with managed switch

Material Options

Material prices below are national averages; availability in Los Angeles may shift costs slightly.

Material	Cost/Unit	Pros	Cons	Best For
Cat6 Ethernet (Standard)	$100-$200 per drop installed	Current standard, 1-10 Gbps capability, widely available, backward compatible	Maximum 10 Gbps only over shorter runs (under 55 meters)	Most residential installs - the right choice for nearly every homeCurrent standard, 1-10 Gbps capability, widely available, backward compatible
Cat6A Ethernet (Future-Proof)	$130-$250 per drop installed	Full 10 Gbps over standard 100-meter runs, better noise isolation, more future-proof	Thicker cable harder to bend around corners, marginally higher cost	Homes with long wire runs, tech-focused homeowners, new constructionFull 10 Gbps over standard 100-meter runs, better noise isolation, more future-proof
Fiber Optic (Backbone)	$300-$600 per run	Unlimited bandwidth, immune to electrical interference, ideal for very long runs	Requires media converters or SFP equipment at each end, more complex to terminate	Very large homes, runs over 100 meters, future multi-gigabit ISP connectionsUnlimited bandwidth, immune to electrical interference, ideal for very long runs
MoCA Adapter (Coax-Based Ethernet)	$50-$120 per adapter pair	Uses existing coaxial TV wiring, 2.5 Gbps capable, no new wire runs needed	Requires existing coax at both locations, latency slightly higher than pure Ethernet	Retrofitting wired connections without running new wireUses existing coaxial TV wiring, 2.5 Gbps capable, no new wire runs needed
Wi-Fi Access Point (In-Ceiling or In-Wall)	$150-$600 per AP installed	Delivers excellent wireless coverage when wired to backbone, hidden flush-mount look	Requires a network drop at each AP location, adds to total drop count	Homes where running cable everywhere isn't practical but better Wi-Fi coverage is neededDelivers excellent wireless coverage when wired to backbone, hidden flush-mount look

Other Projects in Los Angeles

Full Kitchen Remodel

Full Bathroom Remodel

Solar Panel Installation

Back to national average for Home Network / Structured Wiring

Los Angeles Estimate

Typical Range

$1,350–$8,100

vs. National Average

35% above national

Cost Multiplier

1.35x

Cost Per per drop

$135–$810

Estimates apply Los Angeles's 1.35x regional cost multiplier to national averages. Actual bids vary by contractor, project scope, and timing.

See national average costs →