How much does a drywall repair cost in Portland?

A drywall repair in Portland typically costs $154-$1,029, 3% above the $450 national average.

What is the cost per repair for a drywall repair in Portland?

Drywall Repair in Portland typically costs $51-$309 per repair.

How long does a drywall repair take?

A drywall repair typically takes 1-2 days (with dry time between coats). The minimum timeline is 2 hours, and complex projects can run 3-4 days (large section, multiple coats, paint).

Can I DIY a drywall repair?

DIY feasibility for a drywall repair is rated High for small repairs / Moderate for medium / Low for texture matching.

Cost to Drywall Repair in Portland, OR (2026)

If you’re budgeting a drywall repair in Portland, most projects run $154-$1,029, 3% above the $450 national average. What moves that number most is usually one thing: Hole Size. On its own it can swing the cost by $75-$1,500, so that’s the decision to slow down on before you sweat the smaller stuff.

Easiest place to save: Batch all repairs into a single contractor visit - minimum charges mean the 5th hole costs almost nothing compared to calling separately for each.

In the West Coast (where Portland sits): Higher tradesperson wages and contractor demand.

$154-$1,029 in Portland

3% above the national average · 1.03x cost multiplier

In Portland, a drywall repair runs $154 to $1,029 on average - about 3% above what homeowners pay nationwide. The West Coast market's labor costs account for most of the gap, with material pricing and local permitting fees adding to the spread. Use the cost table below to compare budget, mid-range, and premium options side by side.

Cost Breakdown in Portland

Line Item	Low	Mid	High
Cost per repair	$51	$154	$309
Materials	$33	$87	$327
Labor	$122	$407	$1,525
Permits	$0	$0	$0
Total	$155+3% vs. national avg	$494+3% vs. national avg	$1,852+3% vs. national avg

Budget

Small nail holes and hairline cracks, single room

Mid-Range

Fist-sized hole (3-6 inch), proper patch with backer, tape, mud, texture match

Premium

Large section replacement (2+ sq ft), texture matching across multiple repairs

Material Options

Material prices below are national averages; availability in Portland may shift costs slightly.

Material	Cost/Unit	Pros	Cons	Best For
Spackle / Joint Compound (Small Holes)	$5-$15 materials	Easy to apply, fast drying, paintable, DIY-friendly	Shrinks slightly when dry, may need two coats, not for large holes	Nail holes, screw holes, hairline cracksEasy to apply, fast drying, paintable, DIY-friendly
Patch Kit with Self-Adhesive Mesh	$10-$25 materials	Easy for 3-6 inch holes, no cutting required, good DIY option	Requires feathering mud over a large area for invisible seam	Medium holes (3-6 inch) in out-of-the-way locationsEasy for 3-6 inch holes, no cutting required, good DIY option
California Patch (Drywall Scrap)	$5-$15 materials	Professional result, uses existing drywall, no backer board needed	More technique required, not a DIY-beginner method	Holes 3-8 inches where a clean result is neededProfessional result, uses existing drywall, no backer board needed
Section Replacement (Cut and Replace)	$50-$150 materials per section	Best result for large or irregular damage, ties into studs	Most labor-intensive, full tape and mud required	Holes over 8 inches, water damage, impact damageBest result for large or irregular damage, ties into studs
Spray Texture	$15-$40 can	Matches orange peel and light knockdown texture well	Harder to match heavy knockdown or skip trowel, overspray risk	DIY texture matching on orange peel or popcorn-adjacent finishesMatches orange peel and light knockdown texture well

Other Projects in Portland

Earthquake Retrofitting / Seismic Retrofit

Roof Replacement (Asphalt Shingles)

Full Kitchen Remodel

Back to national average for Drywall Repair

Portland Estimate

Typical Range

$154-$1,029

vs. National Average

3% above national

Cost Multiplier

1.03x

Cost Per repair

$51-$309

This 1.03x estimate prices Portland labor from BLS Occupational Employment and Wage Statistics (May 2025) and applies a lighter regional adjustment to materials and permits, which vary less by metro than labor does. Actual bids vary by contractor, project scope, and timing.

See national average costs →