Cost to Dishwasher Installation in Memphis, TN (2026)
If you’re budgeting a dishwasher installation in Memphis, most projects run $93-$295, 16% below the $190 national average. What moves that number most is usually one thing: Replacement vs. First-Time Installation. On its own it can swing the cost by $110 - $600, so that’s the decision to slow down on before you sweat the smaller stuff.
Easiest place to save: Buy the dishwasher from a big-box retailer and add their installation add-on at checkout - Home Depot and Lowes both offer basic installation add-ons for $110-$159 that include haul-away, which is often cheaper than hiring an independent plumber
In the Southeast (where Memphis sits): Lower labor rates across the region; Florida coastal markets run slightly higher due to licensed trade minimums.
$93-$295 in Memphis
16% below the national average · 0.84x cost multiplier
Expect to pay $93-$295 for a dishwasher installation in Memphis, about 16% below the national benchmark. The Southeast region's contractor market and material costs account for most of this difference. The detailed breakdown below shows how budget, mid-range, and premium projects compare at Memphis prices.
Cost Breakdown in Memphis
| Line Item | Low | Mid | High |
|---|---|---|---|
| Cost per installation | $63 | $160 | $506 |
| Materials | $0 | $45 | $137 |
| Labor | $89 | $134 | $285 |
| Permits | $0 | $0 | $68 |
| Total | $89-19% vs. national avg | $179-17% vs. national avg | $490-15% vs. national avg |
Budget
Direct swap of an existing dishwasher using existing water supply, drain, and electrical connections. No modifications needed - the installer disconnects the old unit, slides in the new one, and reconnects. Typical of a big-box store or appliance retailer installation add-on.
Mid-Range
Replacement where the supply line or drain hose needs to be rerouted or replaced, or a new braided stainless supply line and angle-stop valve are required. New mounting brackets and junction box cover may also be needed. Most homeowner upgrades fall into this range.
Premium
First-time installation in a kitchen that has never had a built-in dishwasher. Requires running a new hot water supply line, adding a drain connection at the sink drain or garbage disposal, and installing a dedicated 120V/15A or 20A electrical circuit. Permits required in many jurisdictions.
Material Options
Material prices below are national averages; availability in Memphis may shift costs slightly.
| Material | Cost/Unit | Best For |
|---|---|---|
| Braided Stainless Supply Line (3/8 in.) | $12-$25 each | Any replacement install; should be replaced any time the old supply line is rubber or shows crackingFlexible, kink-resistant, rated for 125 PSI - far more durable than the rubber lines that shipped with older dishwashers |
| Angle-Stop Shutoff Valve (3/8 in. compression) | $10-$30 each | Any installation where no dedicated shutoff exists, or where the existing valve is corroded or a gate-type valveProvides a dedicated water shutoff for the dishwasher without turning off the whole kitchen supply; required in most jurisdictions |
| Drain Air Gap (countertop or cabinet) | $8-$35 each | New installations, California kitchens, or any kitchen without an existing high-loop drain configurationPrevents backflow of sewage into the dishwasher if the drain gets clogged; required by plumbing code in California and several other states |
| Electrical Junction Box and Strain Relief | $8-$20 kit | First-time installations or whenever the existing junction box is absent or shows corrosionProvides a safe, code-compliant electrical connection point inside the dishwasher compartment; protects wire connections from moisture |
Other Projects in Memphis
Memphis Estimate
Typical Range
$93-$295
vs. National Average
16% below national
Cost Multiplier
0.84x
Cost Per installation
$63-$506
This 0.84x estimate prices Memphis labor from BLS Occupational Employment and Wage Statistics (May 2025) and applies a lighter regional adjustment to materials and permits, which vary less by metro than labor does. Actual bids vary by contractor, project scope, and timing.
See national average costs →