Cost to Wall Insulation (Blown-In) in Dallas, TX (2026)
If you’re budgeting a wall insulation (blown-in) in Dallas, most projects run $958-$4,788, 4% below the $2,500 national average. What moves that number most is usually one thing: Wall Area (Square Feet). On its own it can swing the cost by $500 - $4,000, so that’s the decision to slow down on before you sweat the smaller stuff.
Easiest place to save: The IRA 30% Energy Efficient Home Improvement Credit covers blown-in wall insulation costs up to $1,200 per year. Combine this with utility rebates to cut your net cost by 40-60%.
In the Southeast (where Dallas sits): Lower labor costs and competitive market keep prices below the national average. Humidity management matters more here - ensure proper vapor control in the wall assembly, particularly in coastal climates. Some contractors recommend fiberglass over cellulose in high-humidity Gulf Coast areas.
$958-$4,788 in Dallas
4% below the national average · 0.96x cost multiplier
In Dallas, a wall insulation (blown-in) runs $958 to $4,788 on average - about 4% below what homeowners pay nationwide. The Southeast market's labor costs account for most of the gap, with material pricing and local permitting fees adding to the spread. Use the cost table below to compare budget, mid-range, and premium options side by side.
Cost Breakdown in Dallas
| Line Item | Low | Mid | High |
|---|---|---|---|
| Cost per sq ft | $1 | $2 | $4 |
| Materials | $386 | $869 | $1,930 |
| Labor | $763 | $1,716 | $3,337 |
| Permits | $0 | $0 | $193 |
| Total | $1,149-4% vs. national avg | $2,585-4% vs. national avg | $5,460-4% vs. national avg |
Budget
Blown-in cellulose, 1,000 sq ft of exterior wall, drill-and-fill method, patch holes
Mid-Range
Dense-pack cellulose or fiberglass, 2,000 sq ft, existing home retrofit with patching
Premium
Spray foam or high-performance dense-pack, full exterior envelope, older home
Material Options
Material prices below are national averages; availability in Dallas may shift costs slightly.
| Material | Cost/Unit | Best For |
|---|---|---|
| Blown-In Cellulose (Standard) | $1.00 - $2.00 per sq ft installed | Most retrofits - the default choice for drill-and-fill wall insulationRecycled content, excellent air-sealing properties, R-3.5/inch, fire-treated, widely available |
| Blown-In Fiberglass (Standard) | $1.00 - $2.00 per sq ft installed | Humid climates where moisture management is a concernDoes not settle, moisture-resistant, R-2.2-2.7/inch, lighter than cellulose |
| Dense-Pack Cellulose | $1.50 - $2.50 per sq ft installed | Exterior walls where settling would reduce performance, high-performance retrofitsHigher density (3.5 lbs/cubic ft) virtually eliminates settling, better air sealing than standard blown-in |
| Open-Cell Spray Foam (R-3.7/inch) | $2.00 - $3.50 per sq ft installed | New construction or gut renovations where walls are already openExcellent air sealing, fills irregular cavities completely, soft and flexible |
| Closed-Cell Spray Foam (R-6.5/inch) | $3.00 - $5.00 per sq ft installed | New construction, below-grade walls, extremely cold climates needing maximum R-valueHighest R-value per inch, acts as vapor barrier, rigid structural improvement |
Other Projects in Dallas
Dallas Estimate
Typical Range
$958-$4,788
vs. National Average
4% below national
Cost Multiplier
0.96x
Cost Per sq ft
$1-$4
This 0.96x estimate prices Dallas labor from BLS Occupational Employment and Wage Statistics (May 2025) and applies a lighter regional adjustment to materials and permits, which vary less by metro than labor does. Actual bids vary by contractor, project scope, and timing.
See national average costs →