Cost to Ductwork Installation in Virginia Beach, VA (2026)
If you’re budgeting a ductwork installation in Virginia Beach, most projects run $1,908-$7,633, 5% below the $3,800 national average. What moves that number most is usually one thing: Duct Material: Flex vs. Sheet Metal vs. Fiberglass. On its own it can swing the cost by $3 - $20 per linear foot, so that’s the decision to slow down on before you sweat the smaller stuff.
Easiest place to save: Before replacing ducts, have a duct leakage test done ($150-$300) - if your system leaks less than 10% of total flow, sealing may be sufficient instead of replacement, saving thousands.
In the Mid-Atlantic (where Virginia Beach sits): Ductwork in attics is common here, which keeps access costs down. Competitive HVAC market with strong installer availability holds labor rates 8-14% below the national average. Insulation of attic ducts is especially important given extreme summer heat.
$1,908-$7,633 in Virginia Beach
5% below the national average · 0.95x cost multiplier
Homeowners in Virginia Beach typically spend $1,908-$7,633 on a ductwork installation, about 5% below the national average. Labor rates and contractor availability in the Mid-Atlantic region drive much of the price difference. Permit requirements and material delivery costs also play a role. See the full tier-by-tier breakdown below before requesting bids.
Cost Breakdown in Virginia Beach
| Line Item | Low | Mid | High |
|---|---|---|---|
| Cost per linear ft | $10 | $19 | $38 |
| Materials | $615 | $1,537 | $3,587 |
| Labor | $1,082 | $2,254 | $5,408 |
| Permits | $308 | $513 | $820 |
| Total | $2,005-5% vs. national avg | $4,304-4% vs. national avg | $9,815-5% vs. national avg |
Budget
Flex duct replacement, accessible attic or crawl space, straightforward run
Mid-Range
Sheet metal main trunk with flex branches, new system for 1,500 sq ft
Premium
Sheet metal throughout, exposed basement, complex multi-zone layout, test and balance
Material Options
Material prices below are national averages; availability in Virginia Beach may shift costs slightly.
| Material | Cost/Unit | Best For |
|---|---|---|
| Flexible Duct (Flex Duct) | $4 - $8 per linear foot installed | Branch runs in accessible attics, budget-conscious repairs, short runsCheap, fast to install, flexible routing around obstacles, widely available |
| Sheet Metal (Galvanized Steel) | $12 - $25 per linear foot installed | Main trunk lines, commercial applications, high-performance systemsDurable (40+ year lifespan), smooth interior for maximum airflow, takes mastic sealant well |
| Fiberglass Duct Board | $10 - $18 per linear foot installed | Conditioned attic spaces, commercial buildings, systems with quietness requirementsBuilt-in insulation (R-4 to R-6), lightweight, quieter than metal |
| Insulated Flexible Duct | $6 - $12 per linear foot installed | Branch runs in unconditioned attics or crawl spaces where insulation is neededCombines flex routing with R-6 to R-8 insulation in one product |
| Spiral Round Duct | $15 - $30 per linear foot installed | Exposed basement or industrial-aesthetic installations, high-efficiency systemsExtremely smooth interior (lowest friction loss), visually attractive for exposed installations |
Other Projects in Virginia Beach
Virginia Beach Estimate
Typical Range
$1,908-$7,633
vs. National Average
5% below national
Cost Multiplier
0.95x
Cost Per linear ft
$10-$38
This 0.95x estimate prices Virginia Beach labor from BLS Occupational Employment and Wage Statistics (May 2025) and applies a lighter regional adjustment to materials and permits, which vary less by metro than labor does. Actual bids vary by contractor, project scope, and timing.
See national average costs →