Cost to Ductwork Installation in San Francisco, CA (2026)
If you’re budgeting a ductwork installation in San Francisco, most projects run $2,620-$10,481, 31% above the $3,800 national average. What moves that number most is usually one thing: Duct Material: Flex vs. Sheet Metal vs. Fiberglass. On its own it can swing the cost by $3 - $20 per linear foot, so that’s the decision to slow down on before you sweat the smaller stuff.
Easiest place to save: Before replacing ducts, have a duct leakage test done ($150-$300) - if your system leaks less than 10% of total flow, sealing may be sufficient instead of replacement, saving thousands.
In the West Coast (where San Francisco sits): California's Title 24 building code requires duct leakage testing in new systems, adding $150-$300 to the project. Labor rates are among the highest in the nation. Seismic bracing requirements for ductwork add cost in earthquake zones.
$2,620-$10,481 in San Francisco
31% above the national average · 1.31x cost multiplier
Expect to pay $2,620-$10,481 for a ductwork installation in San Francisco, about 31% above the national benchmark. The West Coast region's contractor market and material costs account for most of this difference. The detailed breakdown below shows how budget, mid-range, and premium projects compare at San Francisco prices.
Cost Breakdown in San Francisco
| Line Item | Low | Mid | High |
|---|---|---|---|
| Cost per linear ft | $13 | $26 | $52 |
| Materials | $765 | $1,912 | $4,463 |
| Labor | $1,603 | $3,341 | $8,017 |
| Permits | $383 | $638 | $1,020 |
| Total | $2,751+31% vs. national avg | $5,891+31% vs. national avg | $13,500+31% vs. national avg |
Budget
Flex duct replacement, accessible attic or crawl space, straightforward run
Mid-Range
Sheet metal main trunk with flex branches, new system for 1,500 sq ft
Premium
Sheet metal throughout, exposed basement, complex multi-zone layout, test and balance
Material Options
Material prices below are national averages; availability in San Francisco may shift costs slightly.
| Material | Cost/Unit | Best For |
|---|---|---|
| Flexible Duct (Flex Duct) | $4 - $8 per linear foot installed | Branch runs in accessible attics, budget-conscious repairs, short runsCheap, fast to install, flexible routing around obstacles, widely available |
| Sheet Metal (Galvanized Steel) | $12 - $25 per linear foot installed | Main trunk lines, commercial applications, high-performance systemsDurable (40+ year lifespan), smooth interior for maximum airflow, takes mastic sealant well |
| Fiberglass Duct Board | $10 - $18 per linear foot installed | Conditioned attic spaces, commercial buildings, systems with quietness requirementsBuilt-in insulation (R-4 to R-6), lightweight, quieter than metal |
| Insulated Flexible Duct | $6 - $12 per linear foot installed | Branch runs in unconditioned attics or crawl spaces where insulation is neededCombines flex routing with R-6 to R-8 insulation in one product |
| Spiral Round Duct | $15 - $30 per linear foot installed | Exposed basement or industrial-aesthetic installations, high-efficiency systemsExtremely smooth interior (lowest friction loss), visually attractive for exposed installations |
Other Projects in San Francisco
San Francisco Estimate
Typical Range
$2,620-$10,481
vs. National Average
31% above national
Cost Multiplier
1.31x
Cost Per linear ft
$13-$52
This 1.31x estimate prices San Francisco labor from BLS Occupational Employment and Wage Statistics (May 2025) and applies a lighter regional adjustment to materials and permits, which vary less by metro than labor does. Actual bids vary by contractor, project scope, and timing.
See national average costs →