How much does a attic insulation cost in Jacksonville?

A attic insulation in Jacksonville typically costs $940-$3,291, 6% below the $2,000 national average.

What is the cost per sq ft for a attic insulation in Jacksonville?

Attic Insulation in Jacksonville typically costs $1-$3 per sq ft.

How long does a attic insulation take?

A attic insulation typically takes 4-8 hours. The minimum timeline is 2-4 hours, and complex projects can run 1-2 days.

Can I DIY a attic insulation?

DIY feasibility for a attic insulation is rated Moderate to Good - blown-in insulation is one of the most accessible DIY home improvement projects, especially with rental blowers from home improvement stores.

Cost to Attic Insulation in Jacksonville, FL (2026)

If you’re budgeting a attic insulation in Jacksonville, most projects run $940-$3,291, 6% below the $2,000 national average. What moves that number most is usually one thing: Insulation Type. On its own it can swing the cost by $400 - $3,000, so that’s the decision to slow down on before you sweat the smaller stuff.

Easiest place to save: Rent a blower machine free from Home Depot or Lowes when you buy 10+ bags of insulation - DIY saves 40-60%

In the Southeast (where Jacksonville sits): Lower R-value requirements (R-30 to R-38) and lower labor costs. Focus is on radiant barrier rather than thick insulation.

$940-$3,291 in Jacksonville

6% below the national average · 0.94x cost multiplier

In Jacksonville, a attic insulation runs $940 to $3,291 on average - about 6% below what homeowners pay nationwide. The Southeast market's labor costs account for most of the gap, with material pricing and local permitting fees adding to the spread. Use the cost table below to compare budget, mid-range, and premium options side by side.

Cost Breakdown in Jacksonville

Line Item	Low	Mid	High
Cost per sq ft	$1	$2	$3
Materials	$573	$955	$1,719
Labor	$318	$636	$908
Permits	$0	$48	$96
Design	$48	$239	$573
Total	$939-6% vs. national avg	$1,878-6% vs. national avg	$3,296-6% vs. national avg

Budget

Blown-in fiberglass over existing insulation (top-up to R-38), 1,000 sq ft attic, basic air sealing

Mid-Range

Blown-in cellulose to R-49, 1,200 sq ft attic, comprehensive air sealing of gaps, can lights, and penetrations

Premium

Spray foam on attic roof deck (creating conditioned attic), R-38 to R-49, 1,200 sq ft, full air sealing, with baffles and ventilation work

Material Options

Material prices below are national averages; availability in Jacksonville may shift costs slightly.

Material	Cost/Unit	Pros	Cons	Best For
Blown-In Fiberglass	$0.60 - $1.20 per sq ft	Cheapest option, non-combustible, does not absorb moisture, pest-resistant	Lower R-value per inch (R-2.5), settles 10-15% over time, does not air seal	Budget topping-off over existing insulation, DIY-friendly with rental blowerCheapest option, non-combustible, does not absorb moisture, pest-resistant
Blown-In Cellulose	$0.80 - $1.50 per sq ft	Good R-value per inch (R-3.5), fills gaps better than fiberglass, made from recycled paper	Absorbs moisture if attic has leaks, settles 15-20% over time, fire retardant can irritate skin	Most attic insulation projects - best balance of cost, performance, and air sealingGood R-value per inch (R-3.5), fills gaps better than fiberglass, made from recycled paper
Fiberglass Batts	$0.70 - $1.50 per sq ft	Widely available, familiar to installers, good for standard joist spacing	Hard to install properly around obstacles, gaps reduce effectiveness dramatically	Open attic floors with consistent joist spacing and no obstructionsWidely available, familiar to installers, good for standard joist spacing
Open-Cell Spray Foam	$1.50 - $2.50 per sq ft	Excellent air sealing, fills irregular spaces, good soundproofing	More expensive, requires professional installation, absorbs moisture	Attic roof deck application in mild climates, soundproofing between floorsExcellent air sealing, fills irregular spaces, good soundproofing
Closed-Cell Spray Foam	$2.50 - $5.00 per sq ft	Highest R-value per inch (R-6.5), air and moisture barrier, adds structural rigidity	Most expensive option, requires professional application, can trap moisture if applied incorrectly	Attic roof deck in cold/wet climates, creating a conditioned attic for HVAC equipmentHighest R-value per inch (R-6.5), air and moisture barrier, adds structural rigidity

Other Projects in Jacksonville

Roof Replacement (Asphalt Shingles)

Heat Pump Installation

Full Bathroom Remodel

Back to national average for Attic Insulation

Jacksonville Estimate

Typical Range

$940-$3,291

vs. National Average

6% below national

Cost Multiplier

0.94x

Cost Per sq ft

$1-$3

This 0.94x estimate prices Jacksonville labor from BLS Occupational Employment and Wage Statistics (May 2025) and applies a lighter regional adjustment to materials and permits, which vary less by metro than labor does. Actual bids vary by contractor, project scope, and timing.

See national average costs →