Cost to Concrete Resurfacing in Sacramento, CA

$1,150–$5,175 in Sacramento

15% above the national average · 1.15x cost multiplier

In Sacramento, a concrete resurfacing runs $1,150 to $5,175 on average — about 15% above what homeowners pay nationwide. The West Coast market's labor costs account for most of the gap, with material pricing and local permitting fees adding to the spread. Use the cost table below to compare budget, mid-range, and premium options side by side.

Cost Breakdown in Sacramento

Line Item	Low	Mid	High
Cost per sq ft	$1	$4	$9
Materials	$288	$805	$2,300
Labor	$575	$1,380	$4,600
Permits	$0	$0	$0
Total	$862+15% vs. national avg	$2,185+15% vs. national avg	$6,900+15% vs. national avg

Budget

Basic thin overlay, crack prep, broom finish. Typical for a 400 sq ft patio at $1-$2/sq ft.

Mid-Range

Full resurfacing overlay with color, broom or light texture finish, 2 coats plus sealer. Typical for a 500 sq ft surface at $2-$5/sq ft.

Premium

Decorative overlay - stamped, exposed aggregate, or microtop finish - on a driveway or pool deck with heavy prep. Typical for 1,000 sq ft at $4-$8/sq ft.

Material Options

Material prices below are national averages; availability in Sacramento may shift costs slightly.

Material	Cost/Unit	Pros	Cons	Best For
Basic Concrete Overlay	$0.50-$1.50/sq ft material	Lowest cost, easy to apply over sound concrete, can be tinted	Thin coverage (1/8 inch) doesn't hide major flaws, less durable than polymer-modified options	Patios and walkways in decent condition needing a cosmetic refreshLowest cost, easy to apply over sound concrete, can be tinted
Polymer-Modified Overlay	$1-$3/sq ft material	Stronger bond to existing concrete, more crack resistance, takes color and texture well	Costs more than basic overlay, requires proper surface prep for adhesion	Driveways, pool decks, and any surface with moderate wear or previous patchingStronger bond to existing concrete, more crack resistance, takes color and texture well
Microtop / Microcement	$3-$8/sq ft material	Ultra-thin (1-2mm), smooth contemporary look, works for indoor and outdoor surfaces	Requires highly skilled applicator, surface must be perfectly clean and sound, higher material cost	Modern pool decks, covered patios, and interior concrete floors where a seamless finish is the goalUltra-thin (1-2mm), smooth contemporary look, works for indoor and outdoor surfaces
Stamped Concrete Overlay	$3-$8/sq ft installed	Mimics stone, brick, or slate patterns at a fraction of the cost of real material, adds significant visual interest	Pattern mats require a skilled contractor, repairs are harder to blend if damaged later	Driveways and patios where homeowners want the look of pavers or stone without full replacement costMimics stone, brick, or slate patterns at a fraction of the cost of real material, adds significant visual interest
Exposed Aggregate Overlay	$2-$5/sq ft installed	Natural pebble or stone surface finish, naturally slip-resistant, durable under vehicle traffic	Texture makes it harder to clean, not suitable for bare feet on coarser aggregates	Pool decks (barefoot-grade aggregate), driveways, and patios where slip resistance mattersNatural pebble or stone surface finish, naturally slip-resistant, durable under vehicle traffic

Other Projects in Sacramento

Full Kitchen Remodel

Hardwood Floor Installation

Central AC Installation

Back to national average for Concrete Resurfacing

Sacramento Estimate

Typical Range

$1,150–$5,175

vs. National Average

15% above national

Cost Multiplier

1.15x

Cost Per sq ft

$1–$9

Estimates apply Sacramento's 1.15x regional cost multiplier to national averages. Actual bids vary by contractor, project scope, and timing.

See national average costs →