Cost to Whole-House Rewiring in New York City, NY (2026)
If you’re budgeting a whole-house rewiring in New York City, most projects run $4,293-$18,400, 23% above the $8,000 national average. What moves that number most is usually one thing: Home Size. On its own it can swing the cost by $2,500 - $25,000, so that’s the decision to slow down on before you sweat the smaller stuff.
Easiest place to save: If your home has an accessible attic and unfinished basement, the electrician can fish most wires without opening walls - saving thousands in drywall repair
In the Northeast (where New York City sits): Older housing stock means more rewiring demand. High labor rates in the Boston-NYC-DC corridor push costs 15-25% above average.
$4,293-$18,400 in New York City
23% above the national average · 1.23x cost multiplier
Homeowners in New York City typically spend $4,293-$18,400 on a whole-house rewiring, about 23% above the national average. Labor rates and contractor availability in the Northeast region drive much of the price difference. Permit requirements and material delivery costs also play a role. See the full tier-by-tier breakdown below before requesting bids.
Cost Breakdown in New York City
| Line Item | Low | Mid | High |
|---|---|---|---|
| Cost per sq ft | $4 | $6 | $10 |
| Materials | $1,815 | $3,630 | $6,655 |
| Labor | $3,101 | $5,581 | $9,302 |
| Permits | $363 | $484 | $605 |
| Total | $5,279+23% vs. national avg | $9,937+23% vs. national avg | $17,167+23% vs. national avg |
Budget
Small home (under 1,200 sq ft), accessible wiring paths, basic NM-B copper wiring, standard outlets and switches, code-minimum circuit count
Mid-Range
Average home (1,500-2,000 sq ft), mix of accessible and closed walls, AFCI/GFCI breakers throughout, dedicated circuits for kitchen and laundry, 200-amp panel
Premium
Large home (2,500+ sq ft), complete drywall removal and replacement, structured wiring for data and entertainment, smart panel, whole-home surge protection, subpanels
Material Options
Material prices below are national averages; availability in New York City may shift costs slightly.
| Material | Cost/Unit | Best For |
|---|---|---|
| Standard NM-B (Romex) Copper Wiring | $0.50 - $1.50 per foot | Interior walls, most residential rewiring projectsIndustry standard, easy for electricians to work with, affordable, meets all residential codes |
| MC (Metal Clad) Cable | $1.50 - $3.00 per foot | Exposed basement runs, jurisdictions requiring metal-clad wiring, commercial-style installationsBuilt-in metal armor for protection, required in some jurisdictions (Chicago, NYC), good for exposed runs |
| THWN Wire in Conduit | $2.00 - $4.00 per foot (wire + conduit) | Outdoor runs, garage wiring, unfinished basement exposed wiring, industrial aestheticsWires can be replaced without opening walls, maximum protection, required for outdoor and garage applications |
| 14 AWG Wire (15-amp circuits) | $0.30 - $0.60 per foot | Bedroom and living room lighting circuits, general-purpose outlet circuitsLighter, easier to pull, less expensive, adequate for lighting and general-purpose outlets |
| 12 AWG Wire (20-amp circuits) | $0.50 - $0.90 per foot | Kitchen small-appliance circuits, bathroom circuits, garage circuits, home office circuitsHandles 20-amp loads, required for kitchen and bathroom circuits, more future-proof |
Other Projects in New York City
New York City Estimate
Typical Range
$4,293-$18,400
vs. National Average
23% above national
Cost Multiplier
1.23x
Cost Per sq ft
$4-$10
This 1.23x estimate prices New York City labor from BLS Occupational Employment and Wage Statistics (May 2025) and applies a lighter regional adjustment to materials and permits, which vary less by metro than labor does. Actual bids vary by contractor, project scope, and timing.
See national average costs →