Cost to Whole-House Rewiring in Los Angeles, CA (2026)
If you’re budgeting a whole-house rewiring in Los Angeles, most projects run $4,067-$17,430, 16% above the $8,000 national average. What moves that number most is usually one thing: Home Size. On its own it can swing the cost by $2,500 - $25,000, so that’s the decision to slow down on before you sweat the smaller stuff.
Easiest place to save: If your home has an accessible attic and unfinished basement, the electrician can fish most wires without opening walls - saving thousands in drywall repair
In the West Coast (where Los Angeles sits): California Title 24, strict permitting, and high electrician wages add 20-35%. Earthquake retrofitting may be required simultaneously.
$4,067-$17,430 in Los Angeles
16% above the national average · 1.16x cost multiplier
In Los Angeles, a whole-house rewiring runs $4,067 to $17,430 on average - about 16% above what homeowners pay nationwide. The West Coast market's labor costs account for most of the gap, with material pricing and local permitting fees adding to the spread. Use the cost table below to compare budget, mid-range, and premium options side by side.
Cost Breakdown in Los Angeles
| Line Item | Low | Mid | High |
|---|---|---|---|
| Cost per sq ft | $3 | $6 | $9 |
| Materials | $1,763 | $3,525 | $6,463 |
| Labor | $2,878 | $5,181 | $8,635 |
| Permits | $353 | $470 | $588 |
| Total | $4,994+16% vs. national avg | $9,411+16% vs. national avg | $16,274+16% vs. national avg |
Budget
Small home (under 1,200 sq ft), accessible wiring paths, basic NM-B copper wiring, standard outlets and switches, code-minimum circuit count
Mid-Range
Average home (1,500-2,000 sq ft), mix of accessible and closed walls, AFCI/GFCI breakers throughout, dedicated circuits for kitchen and laundry, 200-amp panel
Premium
Large home (2,500+ sq ft), complete drywall removal and replacement, structured wiring for data and entertainment, smart panel, whole-home surge protection, subpanels
Material Options
Material prices below are national averages; availability in Los Angeles may shift costs slightly.
| Material | Cost/Unit | Best For |
|---|---|---|
| Standard NM-B (Romex) Copper Wiring | $0.50 - $1.50 per foot | Interior walls, most residential rewiring projectsIndustry standard, easy for electricians to work with, affordable, meets all residential codes |
| MC (Metal Clad) Cable | $1.50 - $3.00 per foot | Exposed basement runs, jurisdictions requiring metal-clad wiring, commercial-style installationsBuilt-in metal armor for protection, required in some jurisdictions (Chicago, NYC), good for exposed runs |
| THWN Wire in Conduit | $2.00 - $4.00 per foot (wire + conduit) | Outdoor runs, garage wiring, unfinished basement exposed wiring, industrial aestheticsWires can be replaced without opening walls, maximum protection, required for outdoor and garage applications |
| 14 AWG Wire (15-amp circuits) | $0.30 - $0.60 per foot | Bedroom and living room lighting circuits, general-purpose outlet circuitsLighter, easier to pull, less expensive, adequate for lighting and general-purpose outlets |
| 12 AWG Wire (20-amp circuits) | $0.50 - $0.90 per foot | Kitchen small-appliance circuits, bathroom circuits, garage circuits, home office circuitsHandles 20-amp loads, required for kitchen and bathroom circuits, more future-proof |
Other Projects in Los Angeles
Los Angeles Estimate
Typical Range
$4,067-$17,430
vs. National Average
16% above national
Cost Multiplier
1.16x
Cost Per sq ft
$3-$9
This 1.16x estimate prices Los Angeles labor from BLS Occupational Employment and Wage Statistics (May 2025) and applies a lighter regional adjustment to materials and permits, which vary less by metro than labor does. Actual bids vary by contractor, project scope, and timing.
See national average costs →